Tuning
the Smallpipes
Tuning
is of course a never ending subject. It is worth noting that there are as many
opinions as to what is ‘correct’ as there are 'pipers in the matter of
chanter tuning, but thankfully, drones are an easier matter.
This
chapter will seek to explain the technical aspect of what can be changed and how.
For now, we will only deal with the basic goal of having a pleasant sounding
‘in tune’ instrument.
Drones
The
drones should be tuned to Low A. Many makers offer pipes with a 'baritone' drone tuned to 'E' as well. Some offer a 'D'.
The
tenor drone should sound the same as low A, without any wavering, and
the drone tuned to E should sound the same as E. The bass drone should
be the same as the tenor but an octave lower, again with no wavering.
You move the upper joint of the drone outwards, lengthening the overall
drone when you want to lower the pitch, and conversely, move it
inwards, shortening it when you wish to raise the pitch.
The
drones can be stopped by tapping your finger lightly over the top, or simply by
putting a cork in them, or 'blutack'.
At the start, with one drone only (put a cork in the chanter stock), slide the top joint up and down and listen to the way the
sound changes. This is to train your ear and to make you aware of how the tone
can be varied in a drone.
Now,
you are aware of how the sound changes – shorter is higher in pitch, longer is
lower, and the quality of the sound, the timbre, changes dramatically as you
move the joint up and down.
Once
you start to feel you know what the sound is like, then slide the drone top to a
position slightly above the hemp line.
Open
a second drone. Move the top joint to an extreme position, either out or in, and
gradually slide it until it makes a steady sound at the same pitch as the other
drone. Repeat this many, many times.
Getting used to this is very important and is worth the effort.
You will notice there will a kind of interference between the drones as
they get closer in pitch, a kind of 'wah wah' effect. This wavering
speeds up as the pitches get closer until they suddenly start to come
into tune.
When
you have got both tenor drones in tune, making a steady sound, then open up the
bass, and do the same. This will be trickier, and you need to pay more attention
to how the overall sound wavers. To begin with, it is quite a difficult to hear
how the bass drone is in tune or not. Be patient and keep experimenting. As with
the tenors, start from an extreme and obvious position.
Doing the E drone (if you have one) last makes it easier to get
the sound right. You are looking for that classic, 'medieval', 'bagpipe'
sound here.
If you have a 'D' drone, make the medieval sound with the upper tenor drone and turn the bass off, to learn how to tune.
Once
you are happy you can tune all the drones to sound together, making an even
and steady tone, then you should put in the
chanter, and start again, this time making the tenor drone the same note as the low A
on the chanter, and again making sure it does not have any wavering in the sound.
This can be difficult as the wavering can be very, very small. That is why it is
important to get used to the different ‘colours’ or timbres of the drones,
as the waving is hidden somewhere in the mass of noise.
Quite
simply, when you have got one drone tuned to the low A of the chanter, repeat
what you did above, and add the others, one at a time.
Do
this only with low A when you are a beginner. If another note on the chanter is
not in tune, you will get a different type of waver and it can be confusing.
This is a matter for advanced tuning.
Chanter
Many
people now use a tuning meter. A company called Korg makes the most popular, and there are also tuner apps on mobile 'phones.
That works too. However, people hear with ears, not meters, and if your
batteries are flat, you need to know how to survive…
If
you want to use a meter, you don’t need this page.
The
tricky stuff about chanter tuning concerns something called ‘temperament’.
This is what Bach’s ‘Woll Temperierte Klavier’ is all about. Beware,
a lot of pseudo-science is floating around 'piping circles concerning this. If
you want to know, check Cambpell and Greated ‘Acoustics for Musicians’ – a
big, thick, easy to read university textbook that covers the matter nicely. Not
all of the great master 'pipers who have written on this subject have done so in
agreement with theoreticians’, musicians’ and physicists’ definitions.
Beware…
Smallpipe chanters are not tuned the same way as highland 'pipe
chanters. They are tuned to 'equal temperament'. This means they sound
more like pianos than highland bagpipes do and your tuning meter should
work better for smallpipes.
Notes
are tuned basically in two ways – moving the reed up and down in its socket,
and putting electrical tape over the holes.
The third way is to do with the metal bridle around the reed.
Moving
the reed affects the top hand more than the bottom because as a percentage, any
movement is greater in relation to a short distance than a longer one.
Tape
on the holes works in two ways – by moving the hole downwards, and by making
the hole smaller, thus changing the length of the tube with ‘end effects’
and by altering the amount of energy allowed to disperse at the point of the
hole. This can also be used to change the colour of the note.
Adding
or removing hemp to the reed helps hold it in place but also can affect some
notes more than others. It can also change the note colours. These are advanced
issues and will not be addressed here. Likewise cutting or scraping parts of the
reed and some people work the bridles on chanter reeds - both issues for
advanced tuning (broadly speaking, squeezing on the sides makes the reed more open, harder to play and lower in pitch).
Low
A and High A are what is called an ‘octave’ apart. That is, they should sound like
the same note. To make them the same, move the reed up or down until it is a
true octave. Check with low G and high G. If they are not an octave try your
best to get them there. When they are very near you can correct with electrical tape.
Low
G can be flattened, or lowered in pitch by putting tape over the sound holes at
the bottom and side of the chanter, but be aware this will affect the Low A and
other notes too.
Not all smallpipe chanters have sound holes.
A
good chanter, using a reed that suits it should have the two octaves in tune.
This is your ideal situation, and when you are picking a reed, this is what you
should be looking for.
If
in doubt, aim to make the top a bit sharp and correct it with tape.
As with everything, experiment.
There
are two very simple ways to tune:
Think of Mozart’s ‘Eine Kleine Nachtmusik’. The beginning contains all the notes you need,
nicely arranged. DADADADFA’, G’EG’EG’ECEA. The intervals, or jumps
between notes are very distinctive. Assuming you have got the octaves correct,
all you need to do now is go through this sequence making what you play sound
like Eine Kleine Nachtmusik. Frequently out of tune notes are D and F, and they
usually need some tape.
Another
way of tuning is by playing a scale very slowly and listening to see if each
step is correct. Think of ‘Doh a Deer’ from the ‘Sound of Music’, but
start with Low A as Soh.
This
is a rudimentary description but should be enough to get you started.
Practice
tuning using these non-destructive methods a lot before you try to do anything
more. You will find that this will suffice until your reed starts to get too old.
You know this as it gets unstable and the tuning changes very quickly.
Because
smallpipe chanter holes are so small, you must make absolutely minimal
adjustments - even a single millimetre has a large effect.